just got a new miller tig welder!

roostingrhino

Roost That Rhino - UTVUnderground Approved
Jun 21, 2009
145
6
0
38
just got my welder setup in the shop and tested it out for the first time, works awsome! this is my first time to use a tig welder.
any tips from some pros on how to lay a roll of dimes?
 

roostingrhino

Roost That Rhino - UTVUnderground Approved
Jun 21, 2009
145
6
0
38
its the new diversion 165 it has a hand control from the factory but i will get a foot pedal also later on. i noticed that it gave me a tan line from where my glove was. i need some sleeves next time
 

roostingrhino

Roost That Rhino - UTVUnderground Approved
Jun 21, 2009
145
6
0
38




yeah its mine i was duning and broke the upper ball joint so i took the tire off and drug it back to camp with a local back hoe. drove to witchita ks 4 hour drive with my uncle to johnathan goodwins shop and he was the only guy around with one... drove back tried to put it on and it was the lower. had to drive back, and he didnt have one in stock so he took one off his personal 1000hp duramax powered h1 he built. he just gave it to me free said he has been there... he is an awsome guy, he is on you tube with his new fuel injection stuff some how he makes his hummer 1000 hp duramax and it gets 28mpg, it is awsome
 

JoeyD23

#utvunderground
Jan 9, 2009
18,569
1,368
113
44
North County San Diego
www.utvunderground.com




yeah its mine i was duning and broke the upper ball joint so i took the tire off and drug it back to camp with a local back hoe. drove to witchita ks 4 hour drive with my uncle to johnathan goodwins shop and he was the only guy around with one... drove back tried to put it on and it was the lower. had to drive back, and he didnt have one in stock so he took one off his personal 1000hp duramax powered h1 he built. he just gave it to me free said he has been there... he is an awsome guy, he is on you tube with his new fuel injection stuff some how he makes his hummer 1000 hp duramax and it gets 28mpg, it is awsome

MagMike builds some of the baddest H1's in the nation. He knows all about the Duramax Swaps, they just turned out an insane H1 build with a duramax swap. Magnum Off Road is a sick shop to take your Hummer's too and purchase your H1 parts and aftermarket equipment.

MAGNUM OFFROAD - Rhino Ranger RZR Prowler Hummer FJ


Also you should check out the thread called XXX Welding Porn in the Magnum Off Road Fabrication Section of our website. It will link you to an RDC thread that has some of the baddets welders showing their work and discussing techniques. UTVUnderground's own ZTFab could fill you in on some advce I am sure. He lays dimes with a tig like nobodys biznass
 

rjv

RJV n' NC - UTVUnderground Approved
Feb 2, 2009
67
3
0
NC
PRACTICE, play scraps, try changing you heat,I beleave your freq is fixed, not sure about post flow and ect. Change your heat by 5 amps at a time, start with your amps at the thickness of material. What rod are you using? Get some super missile rod, it with most materials and lays down great. Practice feeding the rod smoothly. GOOD LUCK.
 

MAGNUM OFFROAD

Official UTVUnderground Sponsor & Founder




yeah its mine i was duning and broke the upper ball joint so i took the tire off and drug it back to camp with a local back hoe. drove to witchita ks 4 hour drive with my uncle to johnathan goodwins shop and he was the only guy around with one... drove back tried to put it on and it was the lower. had to drive back, and he didnt have one in stock so he took one off his personal 1000hp duramax powered h1 he built. he just gave it to me free said he has been there... he is an awsome guy, he is on you tube with his new fuel injection stuff some how he makes his hummer 1000 hp duramax and it gets 28mpg, it is awsome
Wow, small world! We are very good friends with Jonathan, infact, he is the one that taught my brother (MAGMIKE) to do the Hummer Duramax conversions. Good guy for sure! Keith also!
 

Members online

Forum statistics

Threads
17,292
Messages
179,387
Members
12,145
Latest member
felipebenjamin000